Ceiling fan remote hookup

Forgot your Password? We welcome your comments and suggestions. All information is provided "AS IS. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.

How to Wire a Ceiling Fan With a Remote to a Wall Switch

By using our site, you acknowledge that you have read and understand our Cookie Policy , Privacy Policy , and our Terms of Service. I am trying to replace a busted Hunter ceiling fan remote. The receiver unit from the old remote had 5 wires - live and neutral, and then 1 that was labeled "fan out", 1 that was labeled "light out", and 1 that was labeled "common out. The fan unit has 4 wires - 1 green wire that is capped, 1 blue wire labelled "for light", 1 black wire, and 1 white wire.

Or do I need to replace the new remote receiver unit with a different one that has the third "common out" wire? Doing my best to interpret your question: First, call the unit you wire in with the fan the "receiver," since it receives signals from the remote transmitter to control the fan and usually a light. The instructions that came with your receiver should explain what the "common out" is for. Without more clear information it could either be intended for 3-way switches or for switching other lights using the same remote.

In the second case it should just be capped. In either case you should wire the white neutral wires together. You should also ensure that the fan's green wire is connected to a ground. Connect the green to the ceiling fan's green wires and the bare copper ground wire in the ceiling box. Connect all white wires together. This will be the fans white wire, the fan control white wire and the white wire in the ceiling box.

If the fan control does not have a white wire, connect the fan's white wire to ceiling box white wire. This is assuming the new fan control only has one white wire. Home Questions Tags Users Unanswered. How do I install a ceiling fan remote? Ask Question. I only have a single light switch in the room. ThreePhaseEel You should wire it exactly as the directions state. Black from ceiling to black hot from receiver. White from ceiling to white neutral from receiver. Blue from fan to red light from receiver.

Black from fan to black fan from receiver. White from fan to white common from receiver. If the unit was previously controlled by two switches. Tester Tester k 54 Wire it this way. Connect the fan's fan wire to fan control's fan wire. Finally connect the fan control's black wire to the ceiling box's black wire. Sign up or log in Sign up using Google. Sign up using Facebook. Sign up using Email and Password. Post as a guest Name. Email Required, but never shown. Featured on Meta.

Unicorn Meta Zoo 2: What is the role of moderators? Linked 4. Related 2. Hot Network Questions.

Start by turning off the power at the breaker, and verifying it's off with a non- contact voltage tester. Connect all the bare or green grounding. The process of wiring a ceiling fan so that a remote receiver controls the fan and, if present, a light as well, isn't as complex as you might expect. The receiver.

Many homeowners wonder how to install a ceiling fan remote, imagining the convenience of lighting and cooling the room without getting out of bed or off the couch. The benefits continue from there. A remote expands design possibilities by letting you remove visually distracting pull chains.

I removed the motor plastic brake, inserted the battery to the transmitter, set the same dip switch to both the transmitter and receiver and press the button on remote and the wall outlet. Nothing happened.

By using our site, you acknowledge that you have read and understand our Cookie Policy , Privacy Policy , and our Terms of Service. I have 2 wall switches. How do I wire them and still be able to use wall switches?

How to Install a Ceiling Fan

The process of wiring a ceiling fan so that a remote receiver controls the fan and, if present, a light as well, isn't as complex as you might expect. You can wire a new ceiling fan with a remote to a wall switch or retrofit an older fan to accept an aftermarket remote kit. Flip off the circuit breaker controlling the wall switch in the room. Double-check that it is off by mounting a ladder to the ceiling fan. Turn on a non-contact voltage tester and hold it up to the wiring.

Dimmer Switch + Ceiling Fan = Problem

How to Wire a Casablanca Ceiling Fan and Remote Control — The wiring connections for a Casablanca Ceiling Fan are very straight forward because these ceiling fans use their own proprietary remote control system and all of the switching is done at the remote control module which is internal at the ceiling fan, there is no need to install a separate module. Can split the fan from light control. Mounting the fan at top of 2 story stairwell, fine for remote to control the fan and light upstairs, but want the light switch at bottom of stairs to control light, so want to bypass the remote for the light. Skill Level: Beginner to Intermediate. Tools Required: Estimated Time: Depends on personal level experience, ability to work with tools and access to the ceiling fan. Mark, I have installed literally hundreds of ceiling fans and the Casablanca Ceiling Fan is one of the best ceiling fans your customer could ever purchase. The wiring connections for a Casablanca Ceiling Fan are very straight forward because these ceiling fans use their own proprietary remote control system and all of the switching is done at the remote control module which is internal at the ceiling fan, there is no need to install a separate module.

The popularity of ceiling fans continues to grow as more and more homeowners discover dramatic, year-round energy savings. In summer, ceiling fans create cooling breezes, which reduce the strain on air conditioners.

Ceiling fan keeping you cool but leaving you in the dark? For those with inadequate, single bulb lighting or lacking a light fixture altogether, adding a ceiling fan light kit offers a simple and inexpensive solutions to limited lighting.

How to Install a Ceiling Fan Remote

Use this procedure before replacing any Emerson electronic controls. If electronic controls fail to program or pair with an Emerson ceiling fan, or operate properly, the following reset procedure can be easily performed by the end user:. Change the dip switches on the transmitter to a new setting. This will change the frequency. If both the wall control and the hand remote are being used make sure both are set to the same new frequency. Hold the power button for approximately 10 seconds, or until the lights blink if the fan includes lights. For Eco Models Only — The fan will automatically go into high speed conditioning mode. For approximately 5 minutes all controls for the fan will be locked out of function. Once the conditioning mode completes, control to the fan and lights will return to the transmitter. Yes, just go to emersonfans.

Hampton Bay Remote Control Installation issue

By using our site, you acknowledge that you have read and understand our Cookie Policy , Privacy Policy , and our Terms of Service. I am trying to replace a busted Hunter ceiling fan remote. The receiver unit from the old remote had 5 wires - live and neutral, and then 1 that was labeled "fan out", 1 that was labeled "light out", and 1 that was labeled "common out. The fan unit has 4 wires - 1 green wire that is capped, 1 blue wire labelled "for light", 1 black wire, and 1 white wire. Or do I need to replace the new remote receiver unit with a different one that has the third "common out" wire? Doing my best to interpret your question: First, call the unit you wire in with the fan the "receiver," since it receives signals from the remote transmitter to control the fan and usually a light.

Wiring on ceiling/fan light combo with remote and independent wall switches?

Are you having a problem with your Harbor Breeze ceiling fan? The challenge you are having could any of the following:. If you are going to take the fan apart due to a wiring problem, we recommend to also have a multi meter on hand. A multi meter is useful to determine where there is a break in the circuit. Often times, it will be impossible to. The wires running from the box in the ceiling need to be matched up with the two green wires, and ground wires coming from the fan need to be spliced to the bare ground wire.

Hampton Bay Remote Control Installation issue

I love dimmer switches; I use them to control a lot of lights in my home. I recently wrote about overloaded dimmer switches , but the most common problem I find is a dimmer switch connected to a ceiling fan. Standard dimmer switches should never be used to control the fan motor on a ceiling fan because the dimmer could damage the fan motor, or overheat and start a fire. To know whether a dimmer switch is intended for use with a fan, just remove the switch cover; there is typically fine print right on the front of the switch saying whether or not it can be used with a ceiling fan. The photo below left comes from a fan speed controller — this is what needs to be used on a ceiling fan. A safe repair can be as simple as replacing the dimmer switch with a standard toggle switch, but you also lose the ability to dim the light.

How to Install a Ceiling Fan

Fulfillment by Amazon FBA is a service we offer sellers that lets them store their products in Amazon's fulfillment centers, and we directly pack, ship, and provide customer service for these products. Something we hope you'll especially enjoy: If you're a seller, Fulfillment by Amazon can help you grow your business. Learn more about the program. Please make sure that you are posting in the form of a question. Skip to main content.

I love dimmer switches; I use them to control a lot of lights in my home. I recently wrote about overloaded dimmer switches , but the most common problem I find is a dimmer switch connected to a ceiling fan. Standard dimmer switches should never be used to control the fan motor on a ceiling fan because the dimmer could damage the fan motor, or overheat and start a fire. To know whether a dimmer switch is intended for use with a fan, just remove the switch cover; there is typically fine print right on the front of the switch saying whether or not it can be used with a ceiling fan. The photo below left comes from a fan speed controller - this is what needs to be used on a ceiling fan. A safe repair can be as simple as replacing the dimmer switch with a standard toggle switch, but you also lose the ability to dim the light. If the wiring for a ceiling fan is already in place in your home ie - you have separate wires for the fan control and the light control , it should be fairly easy for a qualified person to wire up separate controls for the fan and the light, which will include the ability to dim the light.

How to Convert a Ceiling Fan to Remote Control
Related publications