Ice maker water line hook up

Here is a step-by-step water line installation refrigerator guide. A new refrigerator with a water dispenser and ice maker needs to be hooked up to a COLD water line. Usually behind where a refrigerator is installed, there will be a water valve that you can use to hook cold water to your fridge. If there is no water valve behind your fridge, you will have to run a water line to the closest cold water pipe to get your refrigerator access to water.

How to Hook Up a Water Line to a Refrigerator From the Sink

An ice maker is a great addition to any kitchen and can be simple to install with the right materials. Attach copper tubing to your cold water pipe to create a dedicated cold water line for your new appliance. Run this line to the back of your refrigerator or under-counter ice maker and secure it with a compression joint. Be careful during the installation process to prevent water damage, contact with electric wiring, or damage to other plumbing. This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness.

Together, they cited information from 14 references. Ice Makers. Learn more. Learn more Method 1. Locate the closest cold water source. To install an ice maker you will have to tap into the closest-located cold water pipe. Find this cold water source, which may be found under a sink, below the floor, or in a wall. If you need to drill through the floor or wall to reach the pipe, it is best to hire a professional who will know how to avoid wires, ducts, or other plumbing.

You will need to install a cold water line for either a refrigerator ice maker or an under-counter ice maker. Shut off the water and drain the pipe. Turn off the main water valve before starting your project by turning it clockwise. This valve will likely be located on a perimeter wall of your home, in your basement, or near an outdoor water meter. Open the cold water faucet to let water drain out of the pipe. Attach a saddle valve to a clean spot on the cold water pipe.

A saddle valve is a valve that hugs a water line on both sides and supplies a low pressure stream from it. Wipe the area of your cold water pipe that you will attach the valve onto with a clean, wet cloth. Place a saddle valve onto the pipe and tighten its clamps so that it grips the pipe. Screw the valve in to pierce a hole in the pipe. Slowly turn the handle of the valve in a clockwise direction.

When you meet resistance, keep turning the valve firmly. Continue until the needle pierces through the pipe. Attach 0. Place 1 end of your copper tubing into the valve opening. Screw on a small compression joint to secure the connection. Measure the distance between your ice maker and the cold water pipe before purchasing the copper tubing to get the appropriate length. Turn the water back on. Once you have attached the saddle valve and copper piping, you can turn your water back on.

First, make sure all of your connections are secure. Turn the main water valve counterclockwise to turn the water back on. Open the saddle valve to rinse through the copper piping into a large bucket. Gently turn the handle on your saddle valve counter-clockwise to open the valve. Direct the end of your copper tubing unto a large bucket. Let enough water flow through to fill the bucket, then close the valve. Method 2. Locate the ice maker on your refrigerator. If you are hooking up a refrigerator ice maker, find where it is located on the appliance.

If you have a model of refrigerator that is 10 years old or older, the ice maker, including the part that hooks up to the copper tubing, is likely to be located in the freezer. If you have a newer model, it may be located in the refrigerator door. Run the tubing to your refrigerator. Pull your fridge out to access the back of it. Depending on where you accessed your cold water pipe, carefully run the water line towards the back of your fridge.

Avoid leaving the tubing somewhere it might get damaged, stepped on, or crushed. Try to run it flush against the bottom of your walls or cabinets where it is most likely to be safe. Use a compression fitting to attach the piping to the ice maker. Compression fittings are fittings comprised of an outer nut and inner ring that join 2 pipes together. Ice makers will often come with the appropriate compression fitting for the cold water outlet.

Follow the instructions on your manual to attach the piping properly, as refrigerator and ice maker models vary. Use nylon cable clamps to attach the tubing to your fridge. Avoid leaving the copper tubing hanging behind your fridge. Clip it firmly to the side of the fridge using 0. Use a screwdriver to secure the clamps with standard No. Method 3. Measure the space you have available to install the ice maker.

Using a tape measure, find out the height, length, and width of the space you have chosen to install your ice maker. This will help you narrow down what model of ice maker to purchase. An ice maker would be well-located under your kitchen cabinet to the side of your sink or refrigerator. Choose an ice maker that best fits your needs. Under-counter ice makers are available in a large range of sizes with different production and storage capacities. Smaller models generally yield less ice and are less expensive.

Shop for a model of ice maker with a drain pump. A drain pump is a pump that pulls waste water away from different sources, including ice makers, and brings it to a kitchen drain. Most models of ice maker come with a drain pump installed, which makes the installation of an extra, gravity drain unnecessary.

Invest a bit more money in your ice maker to make sure it has a drain pump installed, which will ensure that it functions better, requires less installation work, and is less likely to leak. Attach the ice maker to your cold water line with a compression fitting. Run your cold water line from the pipe to the back of your under counter ice maker. Gently insert the copper piping into the fixture on your ice maker.

Carefully tighten the compression fitting to secure the connection. To make this connection simple, drill dime-sized holes into the sides of your cupboard with an electric drill to easily thread the copper tubing through it. Wear safety goggles and gloves to protect your eyes and hands from any wood particles that may fly into the air while you do this. Put the ice maker into its place under the counter. Under-counter ice makers are typically very heavy, so have a friend or family member help you move it if necessary.

Once the cold water line is attached, lift the ice maker and gently fit it into its designated spot. As you move the ice maker, be sure to slowly pull the piping out through the holes in the sides of your cupboard to keep it from getting stuck under the machine. Include your email address to get a message when this question is answered. Already answered Not a question Bad question Other. Article Info This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness.

Ice Makers In other languages: Did this article help you? Yes No. Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy. Co-Authored By:. March 29, Related Articles. Thanks for letting us know. Help answer questions Learn more.

Connecting a water line for a refrigerator icemaker and water dispenser is easy with a convenient tee-fitting and flex hose supply tubing. Feed the line down, and then up through the refrigerator hole. Now that the water's off, install the new valve for the icemaker water line. There are a few.

By using our site, you acknowledge that you have read and understand our Cookie Policy , Privacy Policy , and our Terms of Service. Our department just moved physical locations. We were able to bring the fridge from our previous break room, but our new location does not have a water line anywhere nearby for the ice maker. The simple solution, of course, is to just use ice cube trays, but I would really like it to be constantly producing ice not have to rely on coworkers to refill the trays. My thought is to get a gallon container, and hook the water line into the bottom and then set it on top of the fridge.

This add-on accessory addresses one annoyance with the Opal: The Opal's small 2.

An ice maker is a great addition to any kitchen and can be simple to install with the right materials. Attach copper tubing to your cold water pipe to create a dedicated cold water line for your new appliance. Run this line to the back of your refrigerator or under-counter ice maker and secure it with a compression joint.

How to Hook Up a Water Line to a Refrigerator

Imagine the convenience of having cold water or ice cubes any time you want them -- no more filling up pitchers to keep in the refrigerator or waiting for ice cube trays to freeze. But once you've bought a refrigerator with a cold water dispenser and automatic ice maker, you'll still need a way to get water into it. It takes patience, but you can hook a water line up to your refrigerator on your own. Here's how [sources: Family Handyman , Whirlpool ].

How to Install a Water Line for a Refrigerator

Running a water line to a refrigerator to supply its ice maker and drinking water dispenser has never been easier. In most cases, the water line can be run from a kitchen faucet water supply line through the kitchen cabinets and over to the refrigerator. If running the line through the cabinets is not feasible, you might need to run a line through the floor and up to where the refrigerator is located. Flex water supply tubes are available in either a tough plastic nylon mesh or braided steel. Although the braided steel is considerably more expensive, the extra strength it provides is well worth the investment. It can be very inconvenient to move a refrigerator to get at a water line that has failed, so buy the best-quality water supply tube you can. If so, your job is very easy. Turn the water supply valve on and check for leaks. Tighten the fittings as needed, using channel-type pliers or an adjustable wrench. If you don't have a convenient water supply pipe and valve near the refrigerator, you must instead find another spot to hook up the water line.

In my opinion the best way to install an ice maker supply line is to treat it like any other fixture branch. Install a standard tee fitting and a ball valve that will allow you to shut off the water supply to the ice maker without disrupting water to any other fixture in the house.

A refrigerator with an automated ice maker and a built-in water dispenser does absolutely nothing if you do not have a water line to connect to it. You can solve this with an ice maker installation kit that allows you to use the plumbing beneath the sink. The kit provides you with the required parts to hook up a water line to your refrigerator. Find your water supply lines beneath your sink.

How to Hook Up a Water Line to a Refrigerator From the Sink

At first glance, it might seem like portable ice makers are simply smaller versions of undercounter ice makers. This is not the case. There are very distinct similarities and differences between the two, and when shopping for an ice maker , you want to be sure to make the best buying decision possible. In a nutshell, portable ice makers are more convenient for light use. A portable ice maker should supply the ice you need in a variety of different conditions that a traditional undercounter ice maker cannot. A portable ice maker will not take up too much space. You can easily store it in an apartment, home, or business for regular or occasional use. Portable units are also fantastic for use in an RV, boat, or other non-traditional living space. Instead of making last-minute dashes to the store for bags of ice, simply pour water into a portable ice maker. Use it when you need it, and ignore it when you do not.

How To Install A Water Line To Your Refrigerator – Easy Step-By-Step Installation

In this video, This Old House plumbing and heating expert Richard Trethewey taps into a water-supply line. Turn off the water to a nearby cold-water supply line. Use a strip of emery cloth to buff-clean a section of the copper water line. Cut into the cold-water line using a tubing cutter. Push the fitting onto the pipe, then heat the fitting with a propane torch. When the flux starts to bubble, solder the fitting onto the pipe. Thread the connector into the transition fitting; tighten the connector with pliers and an adjustable wrench.

KitchenAid Refrigerator Water Line Installation Kit

Fulfillment by Amazon FBA is a service we offer sellers that lets them store their products in Amazon's fulfillment centers, and we directly pack, ship, and provide customer service for these products. Something we hope you'll especially enjoy: If you're a seller, Fulfillment by Amazon can help you grow your business. Learn more about the program. Please make sure that you are posting in the form of a question. Easy to install using our included quick connect fittings.

Log in or Sign up. Plastic tubing for an ice maker water line??? Nov 17, Location: Hello all, new to the forums here. Is this normal? Or is plastic tubing a viable alternative to copper? The line is ran from my water line at the kitchen sink through my cabinets to the fridge, so perhaps it was for flexibility?? Aug 31, Location:

.

.

How to Connect an Ice Maker - Cheap & Easy
Related publications